**Updated**4wd Testing/Repair Step by Step with Videos and Parts Links - Yamaha Grizzly ATV Forum
501Parts.com

Reply
 
LinkBack Thread Tools Display Modes
post #1 of 21 Old 04-12-2015, 09:37 AM Thread Starter
 
oleblue22's Avatar
 
Join Date: May 2010
Location: Arkansas
Posts: 495
Thanks: 93
Thanked 259 Times in 137 Posts
Rep Power: 86
                     
**Updated**4wd Testing/Repair Step by Step with Videos and Parts Links

Troubleshooting

Need Help Identifying and troubleshooting your 4wd? You’ve came to the right place!


The 4wd system on your Yamaha ATV or Side by Side is operated by a push button switch that sends power to a relay, which in turn sends power to the servo motor, which engages your 2wd, 4wd, and difflock.
Identifying and Locating 4wd Components

Push button switch— Located on the handlebars on ATVs and the dash inside the cab on SxS’s. It let’s you switch from 2wd, 4wd, difflock with the push of a button.
Relays— There are three relays that are responsible for the 4wd operation. On non diff lock models there are two. On ATV’s they’re located either under the seat next to your fusebox or under the front rack near the battery. On SxS’s, they’re located under the front hood in the battery box. If either of these are faulty it can cause problems so always check each one.
Servo Assembly— The servo assembly is the black plastic assembly that’s mounted on the rear or side of your front differential. The servo “motor” (as shown in the pictures) is housed inside the black plastic assembly. This motor is usually the culprit for most 4wd related problems.
While we do have complete servo assemblies available, there is no need to replace the entire assembly unless, A. you have somehow busted the black housing, B. the contacts are burnt inside the housing.
99% of the time, you can remove and open the servo assembly (as shown in the videos) and return your assembly to new condition by replacing the motor only.
There are four different types of servo assemblies. See the pictures below to identify which one is yours.



If you’ve purchased a servo motor and need help installing it, you can either watch our video titled replacing the servo motor, or you can print out the instructions below.
Servo motor Installation Instructions:




Yamaha 4wd Troubleshooting Procedures

I’ve included links to videos and parts. To see clips of the service manual pertaining to these tests look here. Troubleshooting | 501 Parts.com Yamaha 4wd System Repair Parts & Service


Problem 1
— 4wd not engaging, and when the push button is pressed nothing happens.


Step 1— Check the fuse
Step 2— Tap on the relays, one could be stuck (Two black with G8HN# on top and one white relay on most models.) Also check the connections on the servo and relays to make sure they’re connected properly.
Step 3— Remove the front diff servo and proceed to test it (need two c batteries, T-45 tamper proof torx, and a 6 mm allen. Some use 10mm regular hex bolts) see this video.
If it tests bad, you can find a replacement motor here. Products | 501 Parts.com Yamaha 4wd System Repair Parts & Service
If you need the bits to remove it from the front diff you can find them at any parts store or you can order them here. Products | 501 Parts.com Yamaha 4wd System Repair Parts & Service
If it tests good, proceed to next step.
Step 4— Test the three relays. You’ll need a multi-meter set on the lowest ohms setting usually 200, and a short run of wire to power up the relays. See this video.

If they test bad, you can find a replacement here.
Products | 501 Parts.com Yamaha 4wd System Repair Parts & Service
If they test good, proceed to the next step.
Step 5— Test the push button switch (you’ll need a multi-meter set to ohms) see these two videos.



To Test the switch on a 98-01 Grizzly or 00-06 Kodiak, see this link for instructions.

For a switch that tests bad, you could try cleaning it before buying one. See this video.


If it tests bad after cleaning or you just want a new one, you can find it here.
Products | 501 Parts.com Yamaha 4wd System Repair Parts & Service
If it tests good, proceed to the next step.
Step 6— At this point you are certain your servo, relays, and switch are good. Next, you’ll want to start tracing wires looking for anything that’s frayed or broken. Common places for problems are under the fusebox on SxS’s, under the front racks on the ATV’s. Also check the connections under the relays beneath the seat on the ATV’s. You may have to untape and untie your wires to get to the problem.
If you’ve tried all of this and still can’t get it going, you are welcome to call me at 501-658-0219 and I’ll help you through it.


Problem 2
— I have replaced my servo motor or cleaned my servo assembly but now I’ve gotten it out of time and it’s not working properly.


Step 1— One thing that will make life easier is to make sure not to bolt the servo up to the diff before you know for certain it’s working. You can plug the servo in and just let it hang to verify proper operation. You need to have three things synced to 2wd before plugging the servo in. 1. You should have the slide gear inside the diff to 2wd mode. 2wd is to the left if you’re sitting on the seat or to the front of the bike for those that go back and forth instead of left and right. On the Rhinos, move the slide gear to the right for 2wd if you are sitting in the seat. 2. Next, have the button in 2wd. 3. Finally, have the servo itself timed to 2wd. Here are videos on cleaning and timing the servo.






Problem 3 — My ATV or SXS goes into 4wd or diff lock but will not come back out.

Step 1— Try tapping on or swapping your two black relays and see what happens (if something changes then one is bad) proceed to test the relays to determine which one. You will break the clips off removing them. Almost no way around it.
See these videos.



For a replacement Products | 501 Parts.com Yamaha 4wd System Repair Parts & Service


Problem 4
— My relays just click when I try and go in 4wd but I don’t hear the servo working.


Step 1— Ensure the connection on the servo is tight and connected properly. If it is proceed to next step.
Step 2— Remove the front diff servo and proceed to test it (need two c batteries, T-45 tamper proof torx, and a 6 mm allen. Some use 10mm regular hex bolts) see this video.

If it tests bad, you can find a replacement motor here. Products | 501 Parts.com Yamaha 4wd System Repair Parts & Service
If you need the bits to remove it from the front diff you can find them at any parts store or you can order them here. Products | 501 Parts.com Yamaha 4wd System Repair Parts & Service
While you are inside the diff, ensure the slide gear can be moved back and forth with your finger with ease. You may have to roll it a little to get it to move but should move freely. If it does not move freely, you can remove the allen screw cap and then remove the slide rod and gear with an allen wrench. The gear, rod and fork will come out. You can clean the slide rod up with emery cloth or light grit sandpaper.


Problem 5
— The slider on my 4wd push button is stuck and will not go left and right with ease.


Step 1- Watch this video.

It will show you how to disassemble and repair the slider.


Problem 6
— I have a big ride tomorrow and I can’t get the 4wd to work. How do I manually put my ride in 4wd and just leave it until I can troubleshoot it?


Despite what mode you may be stuck in 2wd,4wd, diff lock. You can manually put the diff into whatever mode you like. If I were going to pick a mode to leave the diff in for a ride, it would be 4wd.
Step 1- Remove the servo from the front diff. You’ll see a slide gear inside the diff that moves left and right. Simply move that slide gear to the middle for 4wd. If you want to stay in 2wd, move it to the left for ATV’s and to the right for Rhino’s. Verify 2wd by jacking up the front wheels.
Step 2- Reinstall the servo on the diff being careful not to move the slide gear from where you left it. Enjoy your ride and return to this troubleshooting page when you return to fix your problem.


Problem 7
— My 4wd engages off and on without pressing the button.


If your 4wd is going in and out without pressing the button, it is something that you can fix fairly easy. This is actually a common problem with the 12-15 models. Most of the time, the problem boils down to an intermittent connection. After dealing with this on several occasions, I have found a few things that will fix the issue.
Step 1- Pull the plug off of your servo that’s on the front diff and put a dab of dielectric grease on the contacts and plug it back in. Ensure the connection is tight. Do the same thing to your plug coming from the 4wd switch. This usually fixes the problem. It also doesn’t hurt to apply dielectric grease to the 4wd relays while you’re at it. If you’re still having the problem, proceed to step 2.
Step 2- If you’re still having problems after doing the previous step, remove the switch, clean the contacts inside and reassemble. You can see a video here on how to do so.

If you are still having problems after doing this, you could possibly have a broken or shorted wire somewhere between the switch, relays, and servo. Give the wiring a good once over inspection and see if you can see any obvious problems. Let us know if we can help you further.

Of course this is not an all inclusive list of possible 4wd problems. If you’re having trouble and need help feel free to contact us. Contact Us

Here are two basic videos on how-to replace the servo motor inside the case.

Replacing the Servo Motor Sealed Unit


Replacing the Servo Motor Other Three Types


Yamaha ATV/SxS 4wd System Parts and Repair

4wd problems? Start here..

Troubleshooting | 501 Parts ...

Last edited by oleblue22; 10-25-2015 at 10:08 AM.
oleblue22 is offline  
The Following 7 Users Say Thank You to oleblue22 For This Useful Post:
GrizzlyandAxe (06-22-2015), Grumpy (06-23-2015), Indy_Hawk (10-20-2015), it400 (04-12-2015), Mccdan (06-23-2015), natedog56 (06-22-2015), reogem (04-12-2015)
Sponsored Links
Advertisement
 
post #2 of 21 Old 04-12-2015, 09:53 AM
 
reogem's Avatar
 
Join Date: Aug 2011
Location: Northern WI.
Posts: 5,447
Thanks: 2,110
Thanked 2,303 Times in 1,640 Posts
Rep Power: 97
                     
Hey blue thanks for keeping your vid's current.

Twin sister 16 Kodiak EPS 700 Dirty Egg Salad (Camo)
26" Reptiles
STI HD1 Beadlock Wheels


Hers 16 Kodiak EPS 700 Camo
25" Reptiles
STI HD1 Wheels


2013 Ole blue 700
Putting out to Stud 21365 miles
No eps has MMS
360/120 CVT
UniFilter
Going to have 26" Black water EVOs
on stocker wheels
grezzzless clutch.


Retired..05 camo 660


TRADED IN
11 green 450eps
reogem is offline  
post #3 of 21 Old 06-22-2015, 07:56 PM
 
Join Date: Aug 2013
Location: Englishtown, NJ
Age: 28
Posts: 32
Thanks: 7
Thanked 2 Times in 2 Posts
Rep Power: 0
 
Great post. Having issues with my 660 right now in which my 4x4 button works, but the diff lock does nothing. Will start making my way though this guide.

Andy

03 Grizzly 660 Realtree Hardwood Edition
ITP Rims
26" Sti Mud Trax
Warn Winch
2up Kimplex Seat
GrizzlyandAxe is offline  
Sponsored Links
Advertisement
 
post #4 of 21 Old 06-23-2015, 04:57 AM Thread Starter
 
oleblue22's Avatar
 
Join Date: May 2010
Location: Arkansas
Posts: 495
Thanks: 93
Thanked 259 Times in 137 Posts
Rep Power: 86
                     
Thanks, Grizzlyandaxe. Let me know if I can help.

We just updated our site with more service manuals that may help you.

http://www.501parts.com/downloads/

Yamaha ATV/SxS 4wd System Parts and Repair

4wd problems? Start here..

Troubleshooting | 501 Parts ...

Last edited by oleblue22; 06-23-2015 at 11:07 AM.
oleblue22 is offline  
The Following User Says Thank You to oleblue22 For This Useful Post:
GrizzlyandAxe (06-24-2015)
post #5 of 21 Old 06-23-2015, 11:00 AM
 
Join Date: Aug 2013
Location: Englishtown, NJ
Age: 28
Posts: 32
Thanks: 7
Thanked 2 Times in 2 Posts
Rep Power: 0
 
Awesome. Will check it out after work hopefully! -andy


-Andy
Sent from my iPhone using Tapataptap

Andy

03 Grizzly 660 Realtree Hardwood Edition
ITP Rims
26" Sti Mud Trax
Warn Winch
2up Kimplex Seat
GrizzlyandAxe is offline  
post #6 of 21 Old 06-24-2015, 06:43 PM
 
Join Date: Aug 2013
Location: Englishtown, NJ
Age: 28
Posts: 32
Thanks: 7
Thanked 2 Times in 2 Posts
Rep Power: 0
 
Step 1: fuses good
Step 2: relays good
Step 3: servo works with 4x4 command
Step 4: relays tested good
Step 5: switch tested BAD on the dif lock button, which was the one you actually tested in the end of the video.

Go figure! Glad it was the switch though... the rubber gaskets around the buttons were shot anyway. I need the switch by Friday in NJ - doable?

Andy

03 Grizzly 660 Realtree Hardwood Edition
ITP Rims
26" Sti Mud Trax
Warn Winch
2up Kimplex Seat

Last edited by GrizzlyandAxe; 06-24-2015 at 06:43 PM.
GrizzlyandAxe is offline  
post #7 of 21 Old 06-24-2015, 06:45 PM Thread Starter
 
oleblue22's Avatar
 
Join Date: May 2010
Location: Arkansas
Posts: 495
Thanks: 93
Thanked 259 Times in 137 Posts
Rep Power: 86
                     
Glad you got if figured! What's your zip there? There are ways to get it there by Friday.

Yamaha ATV/SxS 4wd System Parts and Repair

4wd problems? Start here..

Troubleshooting | 501 Parts ...
oleblue22 is offline  
post #8 of 21 Old 06-24-2015, 06:46 PM
 
Join Date: Aug 2013
Location: Englishtown, NJ
Age: 28
Posts: 32
Thanks: 7
Thanked 2 Times in 2 Posts
Rep Power: 0
 
Zip is 07726.

Andy

03 Grizzly 660 Realtree Hardwood Edition
ITP Rims
26" Sti Mud Trax
Warn Winch
2up Kimplex Seat
GrizzlyandAxe is offline  
post #9 of 21 Old 06-24-2015, 06:47 PM Thread Starter
 
oleblue22's Avatar
 
Join Date: May 2010
Location: Arkansas
Posts: 495
Thanks: 93
Thanked 259 Times in 137 Posts
Rep Power: 86
                     
Ok give me a moment and I'll check on it for you.

Yamaha ATV/SxS 4wd System Parts and Repair

4wd problems? Start here..

Troubleshooting | 501 Parts ...
oleblue22 is offline  
post #10 of 21 Old 06-24-2015, 06:47 PM
 
Join Date: Aug 2013
Location: Englishtown, NJ
Age: 28
Posts: 32
Thanks: 7
Thanked 2 Times in 2 Posts
Rep Power: 0
 
Found this nifty guy... https://www.usps.com/priority-mail/map/

Andy

03 Grizzly 660 Realtree Hardwood Edition
ITP Rims
26" Sti Mud Trax
Warn Winch
2up Kimplex Seat
GrizzlyandAxe is offline  
post #11 of 21 Old 06-24-2015, 06:53 PM Thread Starter
 
oleblue22's Avatar
 
Join Date: May 2010
Location: Arkansas
Posts: 495
Thanks: 93
Thanked 259 Times in 137 Posts
Rep Power: 86
                     
USPS priority express will put it there Friday by 3:00. It's $20. $85 for the switch. Will that work for you?

Yamaha ATV/SxS 4wd System Parts and Repair

4wd problems? Start here..

Troubleshooting | 501 Parts ...
oleblue22 is offline  
post #12 of 21 Old 06-24-2015, 06:54 PM
 
Join Date: Aug 2013
Location: Englishtown, NJ
Age: 28
Posts: 32
Thanks: 7
Thanked 2 Times in 2 Posts
Rep Power: 0
 
eep. what's it for just regular priority?

Andy

03 Grizzly 660 Realtree Hardwood Edition
ITP Rims
26" Sti Mud Trax
Warn Winch
2up Kimplex Seat
GrizzlyandAxe is offline  
post #13 of 21 Old 06-24-2015, 06:59 PM Thread Starter
 
oleblue22's Avatar
 
Join Date: May 2010
Location: Arkansas
Posts: 495
Thanks: 93
Thanked 259 Times in 137 Posts
Rep Power: 86
                     
Regular priority is $6. May or may not have it by Friday though.

Yamaha ATV/SxS 4wd System Parts and Repair

4wd problems? Start here..

Troubleshooting | 501 Parts ...
oleblue22 is offline  
post #14 of 21 Old 06-24-2015, 07:00 PM
 
Join Date: Aug 2013
Location: Englishtown, NJ
Age: 28
Posts: 32
Thanks: 7
Thanked 2 Times in 2 Posts
Rep Power: 0
 
Eh. Give it a shot - I'll order now.

Andy

03 Grizzly 660 Realtree Hardwood Edition
ITP Rims
26" Sti Mud Trax
Warn Winch
2up Kimplex Seat
GrizzlyandAxe is offline  
post #15 of 21 Old 06-24-2015, 07:01 PM Thread Starter
 
oleblue22's Avatar
 
Join Date: May 2010
Location: Arkansas
Posts: 495
Thanks: 93
Thanked 259 Times in 137 Posts
Rep Power: 86
                     
Ok can you pm me your name and email and I'll send you an invoice.

Yamaha ATV/SxS 4wd System Parts and Repair

4wd problems? Start here..

Troubleshooting | 501 Parts ...
oleblue22 is offline  
Reply

  Lower Navigation
Go Back   Yamaha Grizzly ATV Forum > Site Sponsor Forums > 501Parts.com

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
Ready to step it up Rj20 Grizzly Talk 14 10-27-2013 07:27 AM
step by step install with Pic's jimblaney Grizzly Snorkeling 23 01-10-2012 05:21 PM
Step-by-step install instructions for Swisher Plow igxqrrl Grizzly Accessories 7 11-07-2009 01:07 AM
98-01 600 owners, step in please Gearhead559 Grizzly Talk 4 10-18-2009 08:18 AM
Yamaha better step up! lastbornjoker Yamaha Rhino Discussion 19 10-18-2008 05:29 AM

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome