Monster Grunt Clutch KitThis is a discussion on Monster Grunt Clutch Kit within the Grizzly Tech Tips forums, part of the Grizzly Forums category; I just got the Monster grunt clutch kit with 8 weights instead of the standard 4, I run a 06 Grizzly 660 with 27'' mud ...
| Grizzly Tech Tips Technical articles, tips, tricks and advice from the experts and your fellow Grizzly owners. |
 |
Join Date: Nov 2009
Age: 30
Posts: 2
Thanks: 2
Thanked 0 Times in 0 Posts
Rep Power: 0
|
|
11-05-2009, 09:56 PM
|
|
Monster Grunt Clutch Kit
I just got the Monster grunt clutch kit with 8 weights instead of the standard 4, I run a 06 Grizzly 660 with 27'' mud lites.
So my question is install just 4 or all 8 even tho the instructions call for 27'' and below install 4. Would all 8 make a diffrence and will it hut the machine if i put all 8 in ???
|
|
|
|
Join Date: Jun 2009
Age: 42
Posts: 42
Thanks: 1
Thanked 1 Time in 1 Post
Rep Power: 0
Location: inman sc
|
|
11-05-2009, 10:32 PM
|
|
i just bought epi 14g weights. put in 4 W/ 2mm shim mod. seemed work, but i still want to 8. make sure if you have to change your housings not to crack them. took mine apart last nite found 2 were split open. they could not havr been working properly. no ride this wkn waiting for housings to come in.
__________________
09 700 griz FIEPS
28x14 ITP TIRES 108 ss blk wheels
10x14 front ,12x14 rear
2" moose racing lift
heat tape on fuel tank
heat wrap on exhaust
viper 4000 elite winch
click here
photobucket.com/edeuce
|
|
|
|
Join Date: Oct 2009
Age: 59
Posts: 255
Thanks: 8
Thanked 38 Times in 36 Posts
Rep Power: 5
Location: on the Knik River, Alaska
|
|
11-05-2009, 10:50 PM
|
Quote:
Originally Posted by East Coast Grizzly
I just got the Monster grunt clutch kit with 8 weights instead of the standard 4, I run a 06 Grizzly 660 with 27'' mud lites.
So my question is install just 4 or all 8 even tho the instructions call for 27'' and below install 4. Would all 8 make a diffrence and will it hut the machine if i put all 8 in ???
|
Hard to say without knowing how much they way each. Most likely if you put all 8 your machine will rev to high when you are cruising along and you'll end up pulling four of them back out. weigh one of them, how many grams? |
|
|
|
|
The Following User Says Thank You to wayupnorth For This Useful Post:
|
|
B450 Productions
Join Date: Jul 2009
Age: 42
Posts: 1,565
Thanks: 268
Thanked 255 Times in 205 Posts
Rep Power: 11
Location: Rockaway NJ
|
|
11-05-2009, 11:09 PM
|
|
X2 on what wayupnorth said, also welcome to the GC be sure to post a introduction in the new member thread.
Where are you on the east coast?
__________________
2007 Grizzly 450 Camo Butchs Garage,
Videos= http://www.vholdr.com/user/10900, orhttp://www.youtube.com/user/grizzbutch450
Warn rt 2500, Piaa 510 atp, Twin Air, 2R Tip, AP Skids, 26" Zillas, Ams wheels, Rox handgaurds,Yamaha overfenders, GROC member 
|
|
|
|
El Dee
Join Date: Jun 2009
Age: 50
Posts: 595
Thanks: 246
Thanked 98 Times in 82 Posts
Rep Power: 11
Location: Lillington, North Carolina
|
|
11-05-2009, 11:11 PM
|
|
EVEL AS ALWAYS
|
|
|
|
|
The Following User Says Thank You to tgriffin09 For This Useful Post:
|
|
El Dee
Join Date: Jun 2009
Age: 50
Posts: 595
Thanks: 246
Thanked 98 Times in 82 Posts
Rep Power: 11
Location: Lillington, North Carolina
|
|
11-05-2009, 11:17 PM
|
|
EVEL AS ALWAYS
BTW mine is an 07 660  I just added that signature
__________________
07 660, Black ITP SS108's, 28' ZILLAS, Dynatek ignition, full HMF Utility, UNI filter, Dynojet kit, Grunt clutch kit, EHS Racing air box lid mod.....
Last edited by tgriffin09; 11-05-2009 at 11:20 PM..
Reason: add stuff
|
|
|
|
Join Date: Nov 2009
Age: 30
Posts: 2
Thanks: 2
Thanked 0 Times in 0 Posts
Rep Power: 0
|
|
11-06-2009, 07:23 PM
|
|
I am from Cape Breton Island, Canada.
|
|
|
|
Banned
Join Date: Mar 2009
Age: 52
Posts: 1,627
Thanks: 69
Thanked 324 Times in 213 Posts
Rep Power: 0
Location: The Jersey Shore
|
|
11-06-2009, 08:02 PM
|
|
Since 50% of the job is removal of the floorboards and side cover - I would suggest you install 4 weights and test ride w/o installing the floorboards or side cover (just be carefull not to get your pants caught in the belt while riding).
After the initial test with the 4 weights, remove the sheave and install the remaining 4 weights and test again. This will be the easiest way to determine what is best for you.
I would suggest a machined sheave with a billet spacer plate to regain some of the top end you will loose with the weight kit - but that is just my opinion. You should be able to search the posts for my install on the machined sheave and see if it's to you liking.
Best of luck!
JT
|
|
|
|
Join Date: Oct 2009
Age: 53
Posts: 56
Thanks: 4
Thanked 3 Times in 3 Posts
Rep Power: 6
Location: upper michigan
|
|
11-07-2009, 08:06 AM
|
|
im running the 8 weight set for 26-27 in tires with the spacer and 27 inch tires. I only lost about 2mph off the top and it doesnt seem to low geared. As a matter of fact i was expecting more change in the low end then i got.
|
|
|
|
Join Date: Sep 2009
Age: 28
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
|
|
11-07-2009, 10:23 AM
|
I put all eight in mine didnt hurt anything but the axles.02 grizzly 660 with 27in tires cdi upgrade torque master clutch kit  |
|
|
|
|
Lower Navigation
|
|
|
| Thread Tools |
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
All times are GMT -5. The time now is 10:30 AM.
Powered by vBulletin® Version 3.8.5 Copyright ©2000 - 2010, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.3.2
Website by Be Seen Graphics.
|
